Easy Steps to Replace Recoil Cord on a Predator Generator

Table of Contents

1. Introduction
2. The Issue with the Recoil on the Predator 2000 Watt Inverter Generator
3. Tools Required for Fixing the Recoil
4. Step 1: Removing the Recoil Side Panel
5. Step 2: Taking Apart the Generator
6. Step 3: Removing the Air Filter and Bolts
7. Step 4: Detaching the Recoil
8. Step 5: Measuring and Cutting the New Recoil
9. Step 6: Reattaching the Recoil and Cable
10. Step 7: Putting Everything Back Together
11. Conclusion

How to Fix the Recoil on the Predator 2000 Watt Inverter Generator

Is your Predator 2000 watt inverter generator's recoil not working properly? Don't worry, we've got you covered! In this step-by-step guide, we will walk you through the process of fixing the recoil on your Predator 2000 watt inverter generator. With the help of some basic tools and a little bit of patience, you'll have your generator up and running in no time.

Introduction

The Predator 2000 watt inverter generator is a reliable and efficient power source that is commonly used in various settings. However, like any mechanical device, it can experience issues, with the recoil being one of them. The recoil is responsible for allowing you to start the generator by pulling a cord. When it breaks or malfunctions, starting the generator becomes impossible. Fortunately, repairing the recoil is a straightforward process that you can do yourself with the right tools and guidance.

The Issue with the Recoil on the Predator 2000 Watt Inverter Generator

Before we dive into the fix, let's discuss the issue with the recoil on the Predator 2000 watt inverter generator. The recoil is prone to breaking, especially with regular use or mishandling. When the recoil breaks, it becomes impossible to start the generator using the traditional pull cord method. This can be a frustrating problem, particularly if you rely on the generator for power. However, with the right steps and tools, you can easily fix the recoil and get your generator back in working order.

Tools Required for Fixing the Recoil

To fix the recoil on your Predator 2000 watt inverter generator, you will need the following tools:

1. Phillips head screwdriver
2. Harbor Freight Pittsburgh mechanics tool set (or equivalent)
3. Small ratchet with an extension
4. Eight-millimeter socket
5. Ten-millimeter socket
6. Wire cutters

Having these tools ready will save you time and make the process much smoother.

Step 1: Removing the Recoil Side Panel

To access the recoil on your Predator 2000 watt inverter generator, start by removing the recoil side panel. The panel is held in place by screws that can be easily removed using a Phillips head screwdriver. Once the panel is removed, you will have a clear view of the generator's engine and recoil.

Step 2: Taking Apart the Generator

Next, it's time to take apart the generator to access the recoil mechanism. This requires removing the air filter and several bolts. Use a Phillips head screwdriver to remove the bolt holding the air filter in place. Set the air filter aside.

Step 3: Removing the Air Filter and Bolts

With the air filter out of the way, you can now focus on removing the bolts that secure the recoil. There are three bolts that need to be removed: one at the end, one on the other side, and one at the bottom. Use an eight-millimeter socket with a small ratchet and extension to loosen and remove the bolts. Be cautious of any wire connections in the front panel area.

Step 4: Detaching the Recoil

Once the bolts are removed, the recoil can be detached. Gently pull the recoil forward and let it hang. Take note of how the cable is wound in the recoil. To prevent the cable from unwinding, insert a screwdriver into the coil and secure it in place.

Step 5: Measuring and Cutting the New Recoil

To replace the old recoil, you will need to measure and cut a new recoil to the appropriate length. The easiest way to determine the required length is to measure from your shoulder to your fingertips. Cut the new recoil to match this measurement.

Step 6: Reattaching the Recoil and Cable

Now it's time to reattach the new recoil and cable. Feed the cable through the designated hole in the recoil and tie a knot to secure it. Slowly release the coil while keeping a firm hold on the cable to prevent it from unwinding. Ensure the recoil is securely in place.

Step 7: Putting Everything Back Together

With the new recoil in place, it's time to reassemble the generator. Follow the reverse order of the steps mentioned earlier. Remember to tighten the bolts securely, but be cautious not to overtighten. Once everything is back in place, test the recoil by pulling the cord to start the generator.

Conclusion

Fixing the recoil on your Predator 2000 watt inverter generator is a manageable task that you can do yourself with basic tools and know-how. By following the step-by-step guide provided, you'll have your generator up and running again in no time. Remember to exercise caution while working with the generator, and seek professional help if needed. Enjoy the peace of mind that comes with a fully functioning recoil on your generator.

Highlights:

• The recoil on the Predator 2000 watt inverter generator can break, preventing the generator from starting.
• Fixing the recoil is a simple process that can be done with basic tools and a little bit of patience.
• By following the step-by-step guide, you can replace the recoil and have your generator working again in no time.

FAQ

Q: How do I know if my Predator 2000 watt inverter generator's recoil is broken? A: If you are unable to start the generator by pulling the cord or if the cord feels loose, it's likely that the recoil is broken.

Q: Can I use any type of recoil to replace the broken one on my Predator 2000 watt inverter generator? A: It's recommended to use a compatible recoil specifically designed for the Predator 2000 watt inverter generator to ensure proper fit and functionality.

Q: Do I need any special skills to fix the recoil on my generator? A: Basic mechanical knowledge and the ability to use tools are helpful, but the process is simple enough for most DIY enthusiasts to handle.

Q: How long does it take to fix the recoil on a Predator 2000 watt inverter generator? A: The time required to fix the recoil can vary depending on your experience and familiarity with the process. On average, it can take around 1-2 hours.